Gamma 5800 Els STRINGING MACHINE 2 POINT SC MOUNTING (Is Manual de usuario

OWNER’S MANUALIssue 6 - July 2014STRINGING MACHINE5800 Els2 POINT SC MOUNTING

10CONTROL PANEL FEATURESESC Button - Press to return to the Stringing Screen from the Settings Screen, String Length Meter Screen or to cancel a cha

11Settings ScreenPressing the F1 button will open the Settings Screen to view all current machine settings on the same screen and to quickly ma

12Setting TensionTo change the Tension Setting press F2 to increase the Tension Setting in the tens place, F3 to increase the Tension Setting in the

13Permanent Memory SettingsThere are 9 permanent Memory Settings that can be used to store 9 combinations of machine settings. Pressing the MEMOR Y bu

14MACHINE FUNCTIONSSetting the Pulling Speed from the Stringing ScreenTo change the Pulling Speed Setting while in the Stringing Screen, f rst press

15MACHINE FUNCTIONSPre-stretch FunctionThe Pre-stretch function is used to pre-stretch strings by increasing the applied tension by a set percentag

16Knot String FunctionThe Knot String function is used to increase the applied tension by a set percentage over the tension setting on the last

17MOUNTING THE FRAMEMounting Stand AdjustmentWhen mounting a racquet, adjust the Mounting Stands so that the white Racquet Supports on top of the Mo

18Clamp Base OperationTo lock the String Clamp Base to the Turn-table, rotate the Clamp Base Locking Lever clockwise. To release the string Clamp Bas

19Stringing the MainsFollow the manufacturer ’s recommended stringing pattern for one or two piece stringing. To determine which end of the racquet t

2LIMITED WARRANTYGAMMA SPORTS warrants to the original purchaser that the 5800 Els stringing machine (“EQUIPMENT”) purchased is free from defects in m

20Apply tension to the string by pressing the Ten-sion Lever Switch or the Foot Pedal Switch. The String Gripper will move to the right, away

21Clamping the First Main StringSecure the tensioned main string using the remaining String Clamp. Repeat the proce-dure for all of the remaining mai

22When the end of the string exits through the hole on the right, press the ENTER button to “Zero” the meter, and the length of string will be measur

23Storage DrawersThere are two storage drawers located in the Base of the machine. The drawers open from the right side of the Base and lock

24PATHFINDER AWLOnce the awl is inserted, pull the handle of the awl outward while holding the tip section in place. This leaves the outer sheath in

25Gripper Plate Spacing AdjustmentThe Gripper Plates of the String Gripper are ad-justable to accommodate various string gauges and types of string. I

26Adjusting the Clamp BaseIn the event the Locking Lever rotation is insuff cient to ensure smooth operation of the Clamp Base, very minor adjustments

272pt Hold Down Clamp AdjustmentThe 2pt racquet frame Hold Down Clamps have been adjusted at the factory. However, depending on the racquet frame th

28TROUBLESHOOTING TIPSCARE & CLEANINGWith time and use, the clamping surfaces of your machine may become oily or dirty and result in string or cl

29NOTES

3MACHINE FEATURES Electric Constant Pull Tensioner with 11.0 to 90.0 lbs Tension Range Digital Tension Setting with LCD Display Parallel Jaw Lin

30PARTS LIST 6B CAP SCREW 106 STAND BRAKE KNOB 114 SHORT LEG 115 FLAT HEAD SCREW- M8x25 121 LEVELING FOOT 203 TT SCREWS* 210 STRING REEL HO

31PARTS SUMMARYE862102112121152971066B295309MQAC122772762782882652872981211142932996B323322396395MDCSC13289362320327292321313259301312311285283304286

GAMMA SPORTS 200 Waterfront DrivePittsburgh, Pennsylvania 15222 Phone: 800.333.0337 Fax: 412.323.0317 Visit our website at www.gammasports.comCopyrig

45800 ElsUnpacking Instructions & ContentsInstructions for Unpacking and Preparing for AssemblyThe stringing machine is shipped in three cartons,

5Floor Stand Leg AssemblyThe stringing machine uses a four leg Floor Stand design. The legs must be assembled to the Lower Column before use. Remove

6ASSEMBLY INSTRUCTIONSFloor Stand Height AdjustmentThe height of the machine is adjustable from 39” to 46” in approximate 1” increments. To cha

7The String Reel holder pin is an 8 mm rod with threads on both ends and f at surfaces machined on one end. Thread the end of the pin without the f a

8String Clamp InstallationThe post of the String Clamp and tube of the String Clamp base are treated with grease to provide protection against corrosi

9Instructions for Power Connection and ControlsCAUTION ! Before connecting to the power supply, check the voltage source that the machine is being con